Opened 11 years ago

Closed 10 years ago

#243 closed defect (unknown)

acpi loads with "ERROR: cannot set acpi Interrupt

Reported by: guest Owned by: pasha
Priority: major Milestone: Release version 3.13
Component: ACPI PSD Version: 3.09
Keywords: Cc:

Description

acpi loads with "ERROR: cannot set acpi IRQ" otherwise it seems to work, except that APM no longer seems to detect the lid switch on my laptop. using 3.09 acpi and 1.23 apm

no Irq's are shared and my atheros cardbus card is discovered ok. unfortunately the system won't run with this card as it traps when netbind loads. works ok with my wired lan cardbus card.

Attachments (12)

acpica.log (25.6 KB) - added by guest 11 years ago.
ather.log (18.7 KB) - added by guest 11 years ago.
acpi_1.log (33.0 KB) - added by guest 11 years ago.
apm.log (2.8 KB) - added by guest 11 years ago.
ather4.log (33.0 KB) - added by guest 11 years ago.
log taken with atheros card plugged in throughout boot sequence
apm_ather.log (3.0 KB) - added by guest 11 years ago.
apm log taken with atheros card plugged in throughout boot sequence - lid closed and opened again during logging
ather2.log (16.3 KB) - added by guest 11 years ago.
pci log taken with atheros card plugged in throughout boot sequence - note that card does not show on bus
ather3.log (18.7 KB) - added by guest 11 years ago.
pci log taken with atheros card plugged in after acpi is loaded - note that card now shows on bus
apmruns.log (2.0 KB) - added by guest 11 years ago.
with acpi disabled - cover switch puts laptop into suspend
pci_no_acpi.log (147.8 KB) - added by guest 11 years ago.
with acpi disabled - pci log
pci_no_acpi_ather (147.8 KB) - added by guest 11 years ago.
with acpi disabled - pci log - atheros card plugged in - not recognized
pci_no_acpi_ather.2 (147.8 KB) - added by guest 11 years ago.
with acpi disabled - pci log - atheros card plugged in - not recognized

Download all attachments as: .zip

Change History (30)

comment:1 Changed 11 years ago by pasha

do copy acpica$ acpi.log and attach acpi.log here

Changed 11 years ago by guest

comment:2 Changed 11 years ago by guest

here it is - also, if I attach my wlan atheros card before the acpi driver loads, the system will take a very long time to boot - or not at all. If I plug it in after the acpi driver loads

Changed 11 years ago by guest

comment:3 Changed 11 years ago by guest

one more thing - you can see the uhci controller in the pci log - it has a single port - I cant get it working - the uhci driver says that it can't find the controller - any ideas ?

comment:4 Changed 11 years ago by pasha

  • Version changed from 3.08 to 3.09

Changed 11 years ago by guest

Changed 11 years ago by guest

Changed 11 years ago by guest

log taken with atheros card plugged in throughout boot sequence

Changed 11 years ago by guest

apm log taken with atheros card plugged in throughout boot sequence - lid closed and opened again during logging

Changed 11 years ago by guest

pci log taken with atheros card plugged in throughout boot sequence - note that card does not show on bus

Changed 11 years ago by guest

pci log taken with atheros card plugged in after acpi is loaded - note that card now shows on bus

Changed 11 years ago by guest

with acpi disabled - cover switch puts laptop into suspend

Changed 11 years ago by guest

with acpi disabled - pci log

Changed 11 years ago by guest

with acpi disabled - pci log - atheros card plugged in - not recognized

Changed 11 years ago by guest

with acpi disabled - pci log - atheros card plugged in - not recognized

comment:5 Changed 11 years ago by guest

if acpi is enabled and apm is disabled then cover switch works.

comment:6 Changed 11 years ago by pasha

try add /EIS to acpi.psd

comment:7 Changed 11 years ago by guest

no change with /EIS - except now if I leave the wlan card plugged in during boot - pci picks up the vendor but identifies the device as "4013h - unknown" ( instead of 0013h ) so that genmac doesn't load. If I plug it in after acpi loads, genmac loads ( device enumerates correctly on PCI ) but then crashes with a trap 003 when netbind loads. USB device drive is still not loading, even though ACPI correctly identifies it.

comment:8 Changed 11 years ago by guest

with /EIS still APM prevents detection of lid closing. without apm lid works.

comment:9 Changed 11 years ago by guest

any help here on getting the USB to work on this ( see pci log above.. )?? any help here on wlan trap / not loading unless plugged in after acpi loads? maybe some kind of reset right after the driver loads??

comment:10 Changed 11 years ago by guest

  • Priority changed from minor to major

comment:11 Changed 11 years ago by stevenhl

  • Milestone changed from eCS 2.0 to Release version 3.10

comment:12 Changed 10 years ago by guest

e-co:

Pasha told about your ticket: "there is an error on ACPI tables init"

comment:13 Changed 10 years ago by guest

e-co:

1) What is the model of motherboard?

2) Upgrade your BIOS. this may solve all problems.

3) if 2) doesn't help then try boot ACPI.PSD with /EIS switch, grab log

comment:14 Changed 10 years ago by guest

it is a laptop - panasonic cf-m32 there are no bios updates available for it. I'll get you the log... but I'll have to get another NIC first - I returned that one since I couldn't get it to work.

comment:15 Changed 10 years ago by stevenhl

  • Milestone changed from Release version 3.10 to Feedback pending

comment:16 Changed 10 years ago by eco

e-co:

What is the model of your computer? Acer notebook?

comment:17 Changed 10 years ago by eco

Pasha talks: problems with Intel acpi-ca.

in other words.. intel machine reports about problem.

e-co: imho, try upgrade bios, etc read above.

comment:18 Changed 10 years ago by stevenhl

  • Milestone changed from Feedback pending to Release version 3.13
  • Resolution set to unknown
  • Status changed from new to closed

Waited long enough for feedback.

Note: See TracTickets for help on using tickets.