Custom Query (242 matches)

UNIAUD32 displays msg "ERROR: Initialization failed". Thus loading UNIAUD16 halts boot process with msg: "unable to attach 32-bit driver .. Press ...". Machine is custom built with an ASUS M2V motherboard. The only UNIAUD version that works on this machine is UNIAUD32 v. 1.9.21-SVN r465.

Applications sound output (e.g. Z!, Emperoar TV)runs into a loop (repeating sound). It happens randomly, sometimes after a few minutes, sometimes after half an hour. The sound loop can be stopped by pausing the movie or the music stream for a while. After restarting the sound everything is back to normal.

Motherboard: Tyan S2895 Thunder K8WE with 2 X Opteron 275 Dual Core CPUs. The audio in use is:

Bus 0 (PCI Express), Device Number 4, Device Function 0

Vendor 10DEh Nvidia Corp Device 0059h nForce4 AC'97 Audio Controller Command 0007h (I/O Access, Memory Access, BusMaster?) Status 00B0h (Has Capabilities List, Supports 66MHz,

Supports Back-To-Back Trans., Fast Timing)

Revision A2h, Header Type 00h, Bus Latency Timer 00h Minimum Bus Grant 02h, Maximum Bus Latency 05h Self test 00h (Self test not supported) PCI Class Multimedia, type Audio Subsystem ID 289510F1h Unknown Subsystem Vendor 10F1h Tyan Computer Address 0 is an I/O Port : 1800h..18FFh Address 1 is an I/O Port : 1400h..14FFh Address 2 is a Memory Address (0-4GiB) : C8002000h..C8002FFFh System IRQ 11, INT# A New Capabilities List Present:

Power Management Capability, Version 1.1

Supports low power State D1 Supports low power State D2 Does not support PME# signalling Current Power State : D0 (Device operational, no power saving)

I am running eCS 2.0 RC6 with the 14.104a#@_SMP kernel in single processor mode. CONFIG.SYS: PSD=ACPI.PSD /APIC /CD /TMR /!NOD UniAud? 1.1.4 works. I have tried Uniaud194-1924.zip which gives the following within 2 seconds after loading uniaud16.sys:

Trap 0008 ERRCD=0000 ERRACC= ERLIM= EAX=0001174C EBX=f96f01c0 ECX=00011b34 EDX=00000001 ESI=ffdc221c EDI=0001174c EBP=0000000c FLG=00210006 CS:EIP=0168:fff39a20 CSACC=c09b CSLIM=ffffffff SS:ESP=00000000 SSACC=0093 SSLIM=000001ff DS=0160 DSACC=c0f3 DSLIM=ffffffff CR0=8001001b ES=0160 ESACC=c0f3 ESLIM=ffffffff CR2=fa1d4ffc FS=0000 FSACC= FSLIM= GS=0160 GSACC=c0f3 GSLIM=ffffffff

... Location ##0168:fff0f667 - 000f:e667

60000,9084

Internal revision 14.104a_SMP

Uniaud194-211.zip and eCS 2.0 GA give similar results (Trap 0008) although I have not recorded the actual trap screens.

I have attached the unilog output from the WORKING configuration using Uniaud 1.1.4 since I can't get much after the Trap0008.

Is the presence of multiple CPUs or the use of the SMP kernel causing this?

Is there a PCI-X (HD) card that is supported? The only slots I have available are PCI-X.

Is there any additional information that I can provide?

Thanks!