Custom Query (34 matches)

version 1.30

I added the /g:8086:27c0 to get the driver to recognize the controller.

When it tries to load against the controller, it gives me this error on boot:

Found AHCI device Intel Generic (0:31:2 8086:27c0) class:0x01018f OS2AHCI: couldn't determine MMIO base address No adapter found OS2AHCI driver *not* installed

I suppose that the 0:31:2 could have been 0:31.2. I could have copied it down wrong.

I have the type ibms506$ output as well as a log from a d:2. I'd attach them now I if could figure out how to do that. I'll work on getting them added to this ticket.

I tested all AHCI driver up to the latest 1.3.0 eCS 2.2 beta is able to boot in AHCI mode like in IDE mode.

I have following drivers into config.sys and in the following sequence: BASEDEV=OS2AHCI.ADD /n BASEDEV=DANIS506.ADD /!BIOS ... BASEDEV=DANIATAP.FLT BASEDEV=OS2DASD.DMD

My PATA CDROM is never detected ! Why ?

Cheers/2 Remy

I'm out of SATA ports on my mobo (Tyan S2895 K8WE) so I bought a PCIe 4-port SATA card with a Marvell chipset. PCI shows:

Bus 129 (PCI Express), Device Number 0, Device Function 0

Vendor 1B4Bh Marvell Technology Group Ltd. Device 9230h 88SE9230 PCIe SATA 6Gb/s Controller Command 0107h (I/O Access, Memory Access, BusMaster?, System Errors) Status 0010h (Has Capabilities List, Fast Timing) Revision 10h, Header Type 00h, Bus Latency Timer 00h Self test 00h (Self test not supported) Cache line size 64 Bytes (16 DWords) PCI Class Storage, type Serial ATA (AHCI 1.0) Subsystem ID 92301B4Bh Unknown (Generic ID) Subsystem Vendor 1B4Bh Marvell Technology Group Ltd. Address 0 is an I/O Port : 5030h..5037h Address 1 is an I/O Port : 5024h..5027h Address 2 is an I/O Port : 5028h..502Fh Address 3 is an I/O Port : 5020h..5023h Address 4 is an I/O Port : 5000h..501Fh Address 5 is a Memory Address (0-4GiB) : D0500000h..D05007FFh System IRQ 5, INT# A Expansion ROM of 64 KiB decoded by this card, currently disabled New Capabilities List Present:

Power Management Capability, Version 1.2

Does not support low power State D1 or D2 Supports PME# signalling from mode(s) D3hot PME# signalling is currently disabled 3.3v AUX Current required : 0 mA (Self powered) Current Power State : D0 (Device operational, no power saving)

Message Signalled Interrupt Capability

MSI is disabled MSI function can generate 32-bit addresses

PCI Express Capability, Version 2

Device/Port? Type :

Legacy PCI Express Endpoint Device

Device Capabilities :

Unsupported Request Severity is Fatal

Device Status :

Correctable Error Detected Unsupported Request Detected

Link Capabilities :

Maximum Link speed : Unknown (02h)!! Maximum Link Width : x2 Link Port Number : 0

Link Control :

Asynchronous Clocking in Use

Link Status :

Current Link speed : 2.5Gb/s Current Link Width : x2

Unknown Capability (Code 12h)!!

System boots OK with no drives connected. Adding a drive causes a hang during boot. I have recorded the debug log on another machine per the troubleshooting doc.

[d:\]bldlevel os2krnl Build Level Display Facility Version 6.12.675 Sep 25 2001 (C) Copyright IBM Corporation 1993-2001 Signature: @#IBM:14.106#@_SMP IBM OS/2 Kernel Vendor: IBM Revision: 14.106 File Version: 14.106 Description: _SMP IBM OS/2 Kernel

[d:\]bldlevel \os2\boot\OS2AHCI.ADD Build Level Display Facility Version 6.12.675 Sep 25 2001 (C) Copyright IBM Corporation 1993-2001 Signature: @#D Azarewicz:1.32#@##1## 10 Nov 2013 07:58:57 DAZAR1 ::::::@@AHCI

Driver (c) 2013 D Azarewicz

Vendor: D Azarewicz Revision: 1.32 Date/Time?: 10 Nov 2013 07:58:57 Build Machine: DAZAR1 File Version: 1.32 Description: AHCI Driver (c) 2013 D Azarewicz

[d:\]bldlevel \os2\boot\acpi.psd Build Level Display Facility Version 6.12.675 Sep 25 2001 (C) Copyright IBM Corporation 1993-2001 Signature: @#D Azarewicz:3.22.03#@##1## 28 Nov 2013 11:00:28 DAZAR1 ::::03::@ @ACPI based PSD for eCS (c) 2013 D Azarewicz Vendor: D Azarewicz Revision: 3.22.03 Date/Time?: 28 Nov 2013 11:00:28 Build Machine: DAZAR1 File Version: 3.22.3 Description: ACPI based PSD for eCS (c) 2013 D Azarewicz

I have attached the log from the other machine. Is there anything else you need?

Thanks!