| Description |
I have a Realtek ethernet driver working with RTL8169 driver from eCS 2.0. For that driver I need to specify NetAddress?. I installed beta 1, and networking does not start.
Output of ifconfig and lantran.log are attached. PCI dump of the ethernet adapter follows.
Bus 3 (PCI Express), Device Number 0, Device Function 0
Vendor 10ECh Realtek Semiconductor Co., Ltd.
Device 8168h RTL8111/8168B PCI Express Gigabit Ethernet controller
Command 0007h (I/O Access, Memory Access, BusMaster?)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 03h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Network, type Ethernet
Subsystem ID 0DC4105Bh Unknown
Subsystem Vendor 105Bh Foxconn International, Inc.
Address 0 is an I/O Port : E800h..E8FFh
Address 1 is not present or not configured!
Address 2 is a Memory Address (64-bit, Prefetchable) : DEFFF000h
Address 4 is a Memory Address (64-bit, Prefetchable) : DEFF8000h
System IRQ 11, INT# A
Expansion ROM of 128 KiB decoded by this card, currently disabled
New Capabilities List Present:
Power Management Capability, Version 1.2
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
3.3v AUX Current required : 375 mA
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 2
Device/Port? Type :
PCI Express Endpoint Device
Device Capabilities :
Unsupported Request Severity is Fatal
Device Status :
Correctable Error Detected
Unsupported Request Detected
AUX Power Detected
Link Capabilities :
Maximum Link speed : 2.5Gb/s
Maximum Link Width : x1
Link Port Number : 0
Link Control :
Common Clock Configuration In Use
Link Status :
Current Link speed : 2.5Gb/s
Current Link Width : x1
MSI-X Capability
Vital Product Data Capability
VPD Data not present
|
| Description |
The R8169 driver (ver. 0.1.0) works with an add-in card using the 8169 chip, but when I try to use the motherboard's RTL8111E I can ping the router but the machine locks solid as soon as I start Thunderbird -- even with a new profile. Even Ctrl-Alt-Del does not work, and I have to press Reset or power off.
The motherboard is an Asus M5A88-V EVO.
I have had the same result with and without the /VW switch on the ACPI.PSD line (APCI 3.20.02).
|
| Description |
I am running eCS 2.0 on Intel H55 chipset i3 CPU system with 4GB RAM. The NIC is:
Bus 1 (PCI Express), Device Number 0, Device Function 0
Vendor 10ECh Realtek Semiconductor Co., Ltd.
Device 8168h RTL8111/8168B PCI Express Gigabit Ethernet controller
Command 0007h (I/O Access, Memory Access, BusMaster?)
Status 0010h (Has Capabilities List, Fast Timing)
Revision 03h, Header Type 00h, Bus Latency Timer 00h
Self test 00h (Self test not supported)
Cache line size 32 Bytes (8 DWords)
PCI Class Network, type Ethernet
Subsystem ID 76361462h Onboard RTL8111b on MSI P965 Platinum Mainboard (Guess Only!)
Subsystem Vendor 1462h Micro-Star International Co., Ltd.
Address 0 is an I/O Port : D800h
Address 1 is not present or not configured!
Address 2 is a Memory Address (64-bit, Prefetchable) : FAFFF000h
Address 4 is a Memory Address (64-bit, Prefetchable) : FAFF8000h
System IRQ 11, INT# A
Expansion ROM of 128 KiB decoded by this card, currently disabled
New Capabilities List Present:
Power Management Capability, Version 1.2
Supports low power State D1
Supports low power State D2
Supports PME# signalling from mode(s) D0, D1, D2, D3hot, D3cold
PME# signalling is currently disabled
3.3v AUX Current required : 375 mA
Current Power State : D0 (Device operational, no power saving)
Message Signalled Interrupt Capability
MSI is disabled
MSI function can generate 64-bit addresses
PCI Express Capability, Version 2
Device/Port? Type :
PCI Express Endpoint Device
Device Capabilities :
Unsupported Request Severity is Fatal
Device Status :
Correctable Error Detected
Unsupported Request Detected
AUX Power Detected
Link Capabilities :
Maximum Link speed : 2.5Gb/s
Maximum Link Width : x1
Link Port Number : 0
Link Control :
Asynchronous Clocking in Use
Link Status :
Current Link speed : 2.5Gb/s
Current Link Width : x1
MSI-X Capability
Vital Product Data Capability
VPD Data not present
With the latest beta (0.1.3) I cannot connect to the network. LANTRAN.LOG says:
IBM OS/2 NETBIOS 4.0
Adapter 0 has 123 NCBs, 96 sessions, and 6 names available to NETBIOS applications.
NETBIOS 4.0 is loaded and operational.
IBM LANVDD is loaded and operational.
IBM OS/2 LAN Netbind
PRO0021: A general failure occurred when the program tried to bind TCPIP_NIF to R8110_NIF.
TCPBEUI: Logical adapter 0 is trying to bind to TCP/IP interface lan0.
LT00141: Errors occurred while attempting to initialize TCPBEUI.
I am able to connect using the beta dated 2-14-2011 if I set the NETADDRESS manually (I am typing this using that). I tried using the NIF from that beta with the new OS2 file, but it does not work either.
|
